Metapace S-62 Manual de usuario descargar pdf (Pagina 46)

Inicio
Metapace
Lectores De Códigos De Barras
S-62
Manual de usuario

Descarga
Compartir

Compartiendo
Añadir a mis manuales
Imprimir

Barcode symbologies are application-dependent. You may enable or disable any of them,

and configure their parameters according to the requirements of a specific application.

Chapter 3

CHANGING SYMBOLOGY SETTINGS

efe

refix/Suffix

ode

Refer to 4.7 Remove Special Character

Refer to 1.1.6 Addon Security for UPC/EAN

Refer to 4.1 Letter Case

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 83 84

CONTENTS 3
INTRODUCTION 6
USING METAPACE S-2 SOFTWARE 7
SETUP BARCODES 9
Introduction 10
SCANNER INFORMATION 11
Chapter 1 15
1.1 SCANNING MODE 16
Metapace S-2 Software Manual 17
Chapter 1 18
Changing Scanner Settings 18
1.1.5 READ REDUNDANCY 19
1.2.2 POWER-SAVING 21
1.2.3 LOW BATTERY ALARM 21
1.2.1 AUTO POWER OFF 21
1.7 AUTO SENSE 23
1.8 MEMORY MODE 23
SELECTING OUTPUT INTERFACE 25
2.1 KEYBOARD WEDGE 26
2.1.1 KEYBOARD TYPE 26
2.1.2 ALTERNATE COMPOSING 27
2.1.3 ALPHABETS TRANSMISSION 27
2.1.4 DIGITS TRANSMISSION 28
2.1.5 CAPITAL LOCK TYPE 28
2.1.6 CAPITAL LOCK STATE 28
2.1.7 ALPHABETS LAYOUT 29
2.1.8 DIGITS LAYOUT 30
2.1.9 LAPTOP SUPPORT 30
2.1.10 INTER-CHARACTER DELAY 31
2.1.11 INTER-FUNCTION DELAY 31
2.2 RS-232 32
2.2.1 BAUD RATE 32
2.2.2 DATA BITS 32
2.2.3 PARITY 32
Chapter 2 34
Selecting Output Interface 34
2.3 BLUETOOTH HID 35
2.3.1 KEYBOARD TYPE 35
2.3.5 BROADCASTING 37
2.3.6 SNIFF MODE 38
2.4 BLUETOOTH SPP SLAVE MODE 39
2.4.1 AUTHENTICATION 39
2.4.3 SNIFF MODE 40
2.4.4 INTER-FUNCTION DELAY 41
2.4.5 ACK/NAK TIMEOUT 41
 “Set Connection” label 43
 “MAC Address” label 43
2.6 USB HID 44
2.7 USB VIRTUAL COM 45
Chapter 3 46
IN THIS CHAPTER 47
3.1 CODABAR 48
3.2 CODE 25 — INDUSTRIAL 25 49
3.3 CODE 25 — INTERLEAVED 25 50
3.4 CODE 25 — MATRIX 25 50
Chapter 3 52
Changing Symbology Settings 52
3.12 MSI 55
3.13 FRENCH PHARMACODE 56
3.14 ITALIAN PHARMACODE 56
3.15 PLESSEY 57
Transmit Check Digit 59
3.17 TELEPEN 60
Chapter 4 63
4.1 LETTER CASE 64
4.2 CHARACTER SUBSTITUTION 65
Chapter 4 66
Defining Output Format 66
4.4 CODE ID 68
4.4.1 CODE ID SET 1~5 69
4.5 CODE LENGTH 71
 Code Type 72
4.7 REMOVE SPECIAL CHARACTER 73
Chapter 5 74
5.1 FORMAT SELECTION 75
5.1.1 ENABLE EDITING FORMATS 75
5.1.2 EXCLUSIVE DATA EDITING 75
Chapter 5 76
Applying Editing Formats 76
5.2.2 FIELD SETTINGS 77
5.2.3 TRANSMISSION SEQUENCE 79
5.2.4 EXAMPLES 80
Appendix I 82
GRID CONTROL — SCAN CODE 84

Comentarios a estos manuales

Sin comentarios

Metapace S-62 Manual de usuario Pagina 46

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras Metapace S-62